澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票

当前位置:首页-澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票 > 澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票

室外装饰中黑白铁加工的一些细节?

发布人:http://olivierbernier.com   发布时间:2021-05-28 14:01:49

澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票在室外装修工程施工前,应在墙基的挡板上对黑白铁加工墙的底座进行全 面检查,并认真处理黑白铁加工过程中存在的问题。室外装饰中黑白铁加工的一些细节有哪些?

澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票Before the construction of outdoor decoration project, the base of black and white iron processing wall should be checked on the baffle of wall base, and the problems existing in the process of black and white iron processing should be seriously dealt with. What are some details of black and white iron processing in outdoor decoration?

工作的主要内容是挖掘和填充主体工程施工所形成的混凝土墙面,框架柱或器官柱,待切割部分应弹性化,小心切割,并采用一些砌筑平整。凿成的产品是好的,深凹表面应该用水洗涤,然后在刷涂后用水泥砂浆涂抹,直到它与基材的外表面均匀地弄平。

The main content of the work is to excavate and fill the concrete wall, frame column or organ column formed by the construction of the main project. The part to be cut should be elastic, cut carefully, and use some masonry to level. The chiseled product is good. The deep concave surface should be washed with water, and then coated with cement mortar after brushing until it is even with the outer surface of the substrate.

                济南黑白铁加工

澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票门和窗口位置上的检查端口由顶层从顶部到底部弹出。垂直控制线的下框线是拉水平线。为了防止门窗倾斜,门窗不碍事,上下整齐,误差过大。要求的情况是提前做出全 面修正。门窗框架与墙体之间的间隙应密集分层嵌入,特殊人员应作为一个过程仔细完成,基本项目验收应按门窗子项进行设备。

澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票The inspection port on the door and window position is ejected from the top to the bottom by the top layer. The bottom border of the vertical control line is the horizontal line. In order to prevent the doors and windows from tilting, the doors and windows are not in the way, the up and down are neat, and the error is too large. The requirement is to make a comprehensive correction in advance. The gap between the door and window frame and the wall should be embedded in dense layers, special personnel should complete it carefully as a process, and the basic project acceptance should be carried out according to the door and window sub items.

澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票当在框架填充墙的墙壁上开始抹灰时,由于混凝土和粘土砖墙两种不同的水平材料在吸水性和缩短性能上没有差别,这部分会随机产生石膏表面裂缝的质量容易在这一部分,灰的底层预涂有与灰相同的砂浆,并且过渡层施加到接头上,并且在镗孔缩短之后停止生锈操作。

When plastering is started on the wall of frame infilled wall, because there is no difference in water absorption and shortening performance between concrete and clay brick wall, this part will randomly produce the quality of gypsum surface cracks. In this part, the bottom layer of the ash is pre coated with the same mortar as the ash, and the transition layer is applied to the joint, And stop the rusting operation after the boring is shortened.

上一篇:如何对破损通风管道进行修补?
下一篇:如何让通风管道运行时更加安全?

网站首页 关于我们 澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票 澳门金牛版1877-澳门彩1877cc-1877彩票购彩大厅-1877.cc彩票 工程案例 在线留言 联系我们

今日开马网站-105333香港赛马-hkjc香港赛马主页投注-香港神算子97567-香港神算子四肖